Platform and Tray Mounts & Accessories

The Tough Bar Leg Kit is shaped to the vehicle roofline to get maximum strength and protection for the roof of the vehicle.

Innovative ladders fitting system with an elegant, ergonomic design and quick assembly.

The Wedgetail roof rack to suit the Pajero NS-NT fits by removing the factory rails and securing to the existing mounting points on the roof. Once these are provided we attach our Wedge-wing one piece mounting kit to which the Wedgetail platform connects. The advantages of this kind of mounting system don't just stop with a higher load rating and improved aesthetics, but it also allows for easy removal. The wedgetail is wholly removed from the vehicle via ten bolts, leaving only the ten small brackets on the roof.

Never be caught in the dark again while camping, barbecuing outside, or fishing. This portable 47W LED light features a 4.5m/14.7ft telescopic rod so you can install it at any height. It is remote-controlled and can be powered by your car’s battery or 12V outlet, or a 12V power bank.

The mounting rails are custom designed for each vehicle so that the weight of the platform and load is evenly spread over the vehicle roof. The mounting rails are laser cut from 3 mm steel and then zinc electro-plated and powder coated with a matt black finish.

These Wedgetail Adapter plates are made to carry all your favourite Milwaukee Packout storage products, secured with Wedgetail mounting hardware. Zinc Plated & Powder coated, Matte Black.

The Wedgetail Light Mount Grab Handle, is designed to accommodate a large variety of light types in the market. Install your light of choice into the bracket and it's as easy as mounting the bracket and tightening the bolts.

Wedgetail Winged recovery track bracket is designed to carry your recovery boards either North-South or East-West on the Wedgetail platform. Allowing for low and flat mounting of your recovery boards to reduce the vehicles overall height and wind drag. suitable for Maxtrax and current generation Treds that incorporate keyhole mounts. The Wing requires the mounting pins (not supplied in kit) to be purchased through either Tred or Maxtrax depending on the brand of boards you own.

Wedgetail Winged recovery track bracket is designed to carry your recovery boards off the Drivers or Passenger side of the platform. Allowing for a convenient mounting solution that doesn't take up space on the platform, saving room for your other gear. Suitable for Maxtrax and current generation Treds that incorporate keyhole mounts. The Wing requires the mounting pins (not supplied in kit) to be purchased through either Tred or Maxtrax depending on the brand of boards you own.

A roof top tent negates the major hassle of pitching (and breaking down) a tent and also keeps you off the cold ground. Our Roof Top Tent weighs only 43kg and sleeps two comfortably. Use these mounting brackets to attach it to your Front Runner roof rack. These shorter brackets match the Roof Rack's low profile for a clean aesthetic.

Introducing the Jeep Overland Kit (ROLJ1), a light-weight yet durable roof rack system for your off-road rig. Featuring a refined PioneerTM LT tray that minimises added vehicle height and system weight whilst still maintaining durability for your roughest adventures. Combined with the DIY friendly gutter clamp backbone, the entire system is adventure ready with only a 45 minute installation.

Yakima RuggedLine Flat Canopy

The rubber inserts fit into the top channel of the cross bars on all Wedgetail roof racks

Never be stuck in the wild without a bottle opener again. This bottle opener attaches to either side of a Front Runner Roof Rack, so where your rack goes, your bottle opener does too.

Universal Gas Bottle Holder. One size fits 2kg, 4kg or 9kg gas bottle holder. Low Profile & Easy Installation.

The mounting rails are custom designed for each vehicle so that the weight of the platform and load is evenly spread over the vehicle roof. The mounting rails are laser cut from 3 mm steel and then zinc electro-plated and powder coated with a matt black finish.

The patented Zwifloc high tensile channel nut gives you the flexibility to add, remove or reposition accessories anywhere on a Pioneer platform or Reconn-Deck system.

Accessing the top of your Front Runner Slimsport roof rack is easy as ever when you attach a Rack Handle Bracket. The bracket is made of black power-coated steel, adding function without sacrificing aesthetics.

A good table is a camping staple. The biggest issue? Big and flat, they often end up right at the bottom of a pile of stuff in the back of the car, and aren't easy to access when you want a quick setup on the road.

They’re a saviour on tough tracks and sandy beaches, but there’s nothing worse than trying to find a spot to put filthy recovery boards after they’ve just saved your hide. Flush Flat Maxtrax & TRED Mounting Brackets enable safe and secure roof mounting, so they’re right where you need, when you need them most.

The Tracklander Tough Bar is designed to follow the contour of the vehicle roof, fit to existing Mount Points while providing a strong Full Length Support System which evenly distributes the weight of Roof Rack over the strongest section of the Roof Top.

The STOW iT Utility Holder (Large) has been designed to provide the most secure load carrying solution for a high lift jack, or any other item too long to place in the vehicle. This is the big brother to the popular Utility Holder (Regular) so it can carry more - two shovels, multiple fishing rods or a spade/axe combo. The STOW iT Utility Holder (large) is compatible with Rhino-Rack's most popular systems - the Pioneer Platforms, Reconn-Deck, Vortex & Heavy Duty Cross Bars.

The mounting rails are custom designed for each vehicle so that the weight of the platform and load is evenly spread over the vehicle roof. The mounting rails are laser cut from 3 mm steel and then zinc electro-plated and powder coated with a matt black finish.

Built with durability in mind, the Backbone™ Mount Reconn-Deck™ for Ranger maximises your ute tub storage without compromising the safety of all your cargo. City crash and static load tested to ISO standards, the Reconn-Deck with Fit Kit has a total dynamic system load rating up to 105kg on and off-road, and a static load rating up to 250kg.

Built with durability in mind, the Backbone™ Mount Reconn-Deck™ for Hilux maximises your ute tub storage without compromising the safety of all your cargo. City crash and static load tested to ISO standards, the Reconn-Deck with Fit Kit has a total dynamic system load rating up to 105kg on and off-road, and a static load rating up to 250kg.

A roof top tent negates the major hassle of pitching (and breaking down) a tent and also keeps you off the cold ground. Our Roof Top Tent weighs only 43kg and sleeps two comfortably. Use these mounting brackets to attach it to your Front Runner roof rack. These shorter brackets match the Roof Rack's low profile for a clean aesthetic.

Transport your Front Runner Table underneath your roof rack with this noise-free, easy-access solution. These off-road tough brackets can be mounted either parallel or perpendicular to the roof rack's slats giving you the option to access the table from either the side or rear of the vehicle.

A complete under rack table and table-storage solution that allows you to effortlessly load, transport and access your table when out on any adventure. The Under Rack Table Kit mounts underneath your Front Runner Roof Rack and features the Under Rack Table –– which has an aluminum PVDF top and high-strength black powder-coated steel frame –– as well as the brackets, slides, and latches needed to mount it.

A must-have for anyone who owns a Roof Top Tent, our Quick Release Tent Mount Kit allows you to mount and remove it in seconds without any tools. This makes it ideal for those puzzled about garage clearance or who’d prefer not to be driving around with their roof top tents during the workweek. The four lockable latches provide an off-road tough, rattle-free mounting system that is compatible with various soft- and hard-shell rooftop tents.

The mounting rails are custom designed for each vehicle so that the weight of the platform and load is evenly spread over the vehicle roof. The mounting rails are laser cut from 3 mm steel and then zinc electro-plated and powder coated with a matt black finish.